Home Shop About Foote Contact
English Chevron
Belgium EUR Chevron

Log in

Account

Log in

Account

What is in the box?

  • 1 Foote
  • 1 screwdriver flat head/cross head
  • 1 wooden Foote nametag
  • 2 countersunk brass screws M4X16
The content of the box: A Foote, a screwdriver, a nameplate and 2 brass screws.
  • allen key 4 mm
  • 1 allen key cover*

They are already mounted in the side of the foot of Foote.
That way it is always present when you need it, wherever you are.

Closeup of the allen key, its cover and the place where it is mounted in Foote.
  • 1 Vesa-axle
  • 1 Vesa-bracket
  • 4 screws M4x8
A VESA-bracket, a VESA-axle and 4 screws M4x6

Connecting the Vesa-bracket

What do yo need ?

  • 1 Vesa-axle
  • 1 Vesa-bracket
  • 4 screws M4x6
  • 1 mobile monitor with VESA 75x75 mounting holes
  • 1 flat-head screwdriver
Back of a portable monitor, a VESA-bracket, a VESA-axle, a screwdriver and 4 small screws.

Step 1

Turn the monitor with the screen towards the table and gently lay it down with the bottom of the monitor (purple arrow) towards you.

The back of a portable monitor with a orange arrow locating the top and a purple arrow the bottom.

Step 2

Put the Vesa-axle (see red arrow) in the middle of the 4 Vesa-mounting holes of the monitor. The Vesa-axle has 3 protruding parts, 2 with screw holes (green arrows) and 1 without screwholes (yellow arrow). The protruding part without screwhole is supposed to point towards the bottom of the screen.

Show the orientation of the VESA-axle.

Step 3

This step depends on the which side of the monitor the ports for the cables are. The monitor still lies on the table with screen facing the table and the bottom of the screen towards you. If the ports are located on the left side of the monitor proceed to step 3a.If the ports are located on the right side of the monitor proceed to step 3b.

Step 3a - Step 3b

Step 3a: Ports left side
  • The Vesa-bracket has 2 protruding part facing the middle of the axle 
  • Place the Vesa-bracket around the Vesa-axle so 
  1. The screw holes of the monitor match the holes of the Vesa-bracke. 
  2. 1 of the protruding parts is on the left top side and the other on the right bottom ( see arrows )
Stap 3b: Port right side
  • The Vesa-bracket has 2 protruding part facing the middle of the axle 
  • Place the Vesa-bracket around the Vesa-axle so 
  1. The screw holes of the monitor match the holes of the Vesa-bracke. 
  2. 1 of the protruding parts is on the right top side and the other on the left bottom ( see arrows )

Step 4

Use the countersunk M4x8 screws to attach the Vesa-bracket to the back of the monitor.

Fasten the VESA-bracket using the 4 screws.

Connecting Foote to the mobile monitor

What do we need?

  • 1 Mobile monitor with a mounted Vesa-bracket, Tripod-mount or sticky mount *
  • 1 Foote
  • 1 wooden nametag
  • 2 countersunk screws M4x16
  • a screwdriver

* If there is no Vesa-bracket, Tripod-mount of sticky-mount mounted go to the start of the manual!

For the next step is needed: Monitor with mounted VESA-bracket, a Foote, a nametag, 2 brass screws and a screwdriver.

Step 1

The monitor still lies with the screen towards the table, the mount facing upwards and the bottom of the screen towards you. 

The photo displays the Vesa-bracket.

The back of a portable monitor with a mounted VESA-bracket

Step 2

Place Foote on the Vesa-bracket. Make sure that Vesa-axles protruding parts with screw holes ( marked in green ) correspond with the cut-outs of Foote. The Vesa-axles protruding part without a screw hole ( marked in yellow ) has to be between the two middle parts of Foote.

Depicts the interface between the Foote and the VESA-axle.

ATTENTION

Make sure that the correct side of Foote is mounted towards the monitor In photo 1 Foote is mounted correctly.In photo 2 Foote is mounted wrong.
Depicts the wrong orientation of the Foote when mounting it to the portable monitor.
Photo 1
Depicts the right orientation of the Foote when mounting it to the portable monitor.
Photo 2

Step 3

Place the wooden nametag. The 2 countersunk holes have to line up with the 2 screw holes of the Vesa-axle. See the photo for the orientation of the letters.

Shows the orientation of the nametag.

Stap 4

Use the 2 countersunk brass screws M4x16 to fasten the name tag and secure Foote to your monitor.

Fasten the nametag using the 2 brass screws.

Foote is now connected to your monitor

Swivel Foote 90° to align it with your monitor. Depending on the mounting of the Bracket to the monitor you have to turn either left of right.

How schould I use Foote?
The back view of portable monitor with a folded Foote attached to it.